Plumbing 101: A Guide to Bathtub Installation
Plumbing 101: A Guide to Bathtub Installation
Blog Article
How do you actually feel in relation to A Step-by-Step Guide to Installing a Bathtub?
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Setting up a bath tub isn't exactly brain surgery, yet it does require strong plumbing, woodworking, as well as sometimes, tiling skills. Changing an old tub with a brand-new one is additionally a moderately difficult task. If the old tub is conveniently available, the project can move immediately; if you need to open a wall surface to remove the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will certainly need a helper to leave the old bathtub as well as set in the new one. See to it you have actually certified yourself for the task and also fit trying it. Rather than hiring a contractor to take over a halfway-completed job, it is better to consider utilizing one prior to you begin. Opportunities are you might need a specialist plumber to make tube links.
This write-up will help you set up a new bath tub in your shower room if you have actually currently gotten a brand-new tub as well as do not require to alter the setup of your previous water system pipelines.
Your devices as well as product checklist ought to consist of the following:
Planning for the Installation
First of all, the supporting structure provided with the bathroom must be fitted (if needed) according to the producer's guidelines. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is essential to see to it that if the faucet includes a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bath, it is likewise sensible to fit a sustaining plate under the faucets unit to stop strain on the tub.
Fit the versatile faucet ports to the bottom of the two taps using 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you make use of all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath must now prepare to be fitted in its last placement.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installation, then the first thing you need to do is separate the supply of water. After doing so, switch on the faucets to drain pipes any kind of water continuing to be in the system. The process of eliminating the existing faucets can be quite bothersome as a result of the restricted access that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will originate from the pipes. Once the supply pipelines have been removed, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the single faucets from turning throughout this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing compound.
Prior to carrying on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Mounting the Tub
Using the two wood boards under its feet, place the bathtub in the required position. The wood boards are valuable in evenly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four little points.
The following goal is to guarantee that the bath tub is leveled all round. This can be achieved by examining the level and also changing the feet on the tub until the level reviews degree.
To install taps, fit the bottom of the furthest flexible faucet connector to the suitable supply pipeline by making a compression sign up with; then do the exact same for the other faucet.
Activate the water supply and check all joints as well as brand-new pipework for leakages and tighten them if required. Load the tub as well as likewise examine the overflow electrical outlet and also the regular outlet for leakages.
Lastly, fix the bath paneling as described in the producer's instruction manual. Tiling and securing around the bath tub must wait up until the bathtub has actually been utilized at the very least once as this will resolve it right into its final position.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic port to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end provides a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly require lowering couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin making sure that the washers are in place between the tap and also the sink. Protect the tap in position with the maker given backnut. Once the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal tap adapters. The previous type must be linked to the faucet ends first, tightening up only by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bath satisfies the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to crack a rigid seal, triggering the water to penetrate the wall between the bath and the tiling, causing difficulties with wetness and also feasible leakages to the ceiling below.
You can select from a variety of coloured sealants to assimilate your components as well as fittings. They are marketed in tubes as well as cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to always fill up the bathtub with water prior to sealing, to enable the movement experienced when the tub remains in use. The sealer can break rather early if you do not think about this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently offered on the marketplace. It is a good idea to fit the tiles utilizing waterproof or waterproof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our post on Installing A Bathtub. Many thanks for taking the time to read our blog. If you liked our blog posting kindly make sure you remember to pass it around. Thank-you for your time spent reading it.
This Website Report this page